Filter
Top Products
2172-1
Module No. 2172
GETTING ACQUAINTED
Congratulations upon your selection of this CASIO watch. To get the most out
of your purchase, be sure to carefully read this manual and keep it on hand
for later reference when necessary.
About this manual
• Button operations are indicated using the
letters shown in the illustration.
• Each section of this manual provides you
with the information you need to perform
operations in each mode. Further details
and technical information can be found in
the “REFERENCE” section.
Snorkeling/Scuba Diving Precautions
• Make sure that you have received proper diving training before using
this watch underwater.
• Always use the “buddy system” when diving. Never dive alone.
• Note that this watch is NOT a diving computer, and is not capable of
making decompression calculations.
• The depth meter function built into this watch should only be used as
a “back-up” to your standard depth gauge.
• Note that this watch cannot be used in helium atmospheres.
• Though the function of this watch is not affected by magnetism, long
use near a source of magnetism can case the watch itself to become
magnetized. A magnetized watch can interfere with the precision of
readings produced by an underwater compass. To avoid such
problems, keep the watch away from your compass when taking
readings.
5
630
20 00
0
05
1
Before Diving
• Before beginning each dive, check to make sure that the BATT (and/
or RECOVER) message (which indicates that battery power is weak)
and/or ERR message (which indicates sensor malfunction) are not on
the display. If either message is on the display, contact an authorized
CASIO Dealer/Distributor or authorized CASIO Service Point to have
the battery replaced or to have the watch repaired.
• Make sure that the current time setting of the watch is correct.
• Check the glass, case, and band for cracks or chips.
• Make sure that the band is fastened securely around your wrist.
While Diving
• Check to make sure that the timer and depth gauge are operating
properly.
• Warning indicators flashing on the display indicate the possibility of
a data error. For details, see “Warning Indicators”.
• Take care when diving near rocks or coral to avoid scratching or
damaging the watch.
After Diving
• To avoid corrosion, rinse your watch thoroughly with fresh water to
remove salt water, dirt, etc. When possible, soak the watch in fresh
water overnight to make sure that all salt is removed.
• When using a metal band, occasionally clean the gaps in the band
using a soft toothbrush and soapy water. Failure to keep a metal
band clean can result in corrosion of the watch, soiling of clothing, or
irritation of sensitive skin.
CASIO COMPUTER CO., LTD. assumes no responsibility for any
loss, or any claims by third parties that may arise through the use of
this watch.
GENERAL GUIDE
For information on how to read the display, refer to the separate instructions
on each function.
5
630
20 00
0
05
1
5
630
300
0
05
1
x
10 58
11 58
3
82
500
x
10 58
11 58
3
82
500
10 58
20
1
2
000
10 58
4
00
▲
Press D.
Timekeeping Mode
▲
Press C.
Recall Mode
▲
Dive Profile Mode
▲
Alarm Mode
Diving Mode
▲
▲
▲
Hold down C
for two seconds.
Time/Date
Temperature
TIMEKEEPING
Use the Timekeeping Mode to set the current
time and date, and to view the current time.
You also can adjust the display contrast while
in the Timekeeping Mode.
To reset the seconds count to zero
1. In the Timekeeping Mode, hold down A
until the seconds digits start to flash, which
indicates the setting screen.
2. Press D to reset the seconds count to
00.
• Pressing D while the seconds count is in
the range of 30 to 59 resets the seconds to
00 and adds 1 to the minutes. In the range
of 00 to 29, the minutes count is
unchanged.
3. Press A twice to exit the setting screen.
To set the time and date
1. In the Timekeeping Mode, hold down A
until the seconds digits start to flash, which
indicates the setting screen.
• While the seconds digits are flashing, press
D to set the seconds count to
00.
2. Press C to move the flashing in the
sequence shown below to select other
settings.
• See “Daylight Saving Time (DST)” for details on the DST setting and
“Adjusting Display Contrast” for information about contrast.
3. Use C to move the flashing to the hour, minutes, year, month, and day,
and make the settings you want for each.
• While the hour, minutes, year, month, or day setting is flashing, use D (+)
and B (–) to change it.
• When the 12/24-hour setting is selected, press D to toggle between
12-hour (
1CL) and 24-hour (CZL) timekeeping.
5
630
20 00
0
05
1
5
630
20 00
0
05
1
Seconds
Month – Day
Day of week
Hour : Minutes
Year
AM indicator
Seconds
°C/°F M/F
Minutes
Contrast
12/24-Hour
format
DST Hour
Day
Month
Year
MO0403-B