Filter
Top Products
Operation Guide 2872
1
MO0405-EA
Getting Acquainted
Congratulations upon your selection of this CASIO watch. To get the most out
of your purchase, be sure to read this manual carefully and keep it on hand
for later reference when necessary.
Expose the watch to bright light to charge its battery before using it.
You can use this watch even as its battery is being charged by exposure to
bright light.
• Be sure to read “Power Supply” of this manual for important
information you need to know when exposing the watch to bright
light.
Applications
The built-in sensors of this watch measure direction, barometric pressure,
temperature and altitude. Measured values are then shown on the display.
Such features make this watch useful when hiking, mountain climbing, or
when engaging in other such outdoor activities.
If the digital display of the watch is blank...
If the PS indicator is on the display (either
flashing or steady), it means that the watch’s
Power Saving function has turned it off to
conserve power. Power Saving automatically
turns off the display and enters a sleep state
whenever the watch is left for a certain period
where it is dark.
• The initial factory default setting is Power Saving on.
• The watch will recover from the sleep state if you move it to a well-lit area,
*
if you press any button, or if you angle the watch towards your face for
reading.
*
It can take up to two seconds for the display to turn on.
• See “Power Saving” for more information.
Warning!
• The measurement functions built into this watch are not intended for
taking measurements that require professional or industrial precision.
Values produced by this watch should be considered as reasonable
representations only.
• When engaging in mountain climbing or other activities in which losing
your way can create a dangerous or life-threatening situation, always be
sure to use a second compass to confirm direction readings.
• CASIO COMPUTER CO., LTD. assumes no responsibility for any loss,
or any claims by third parties that may arise through the use of this
watch.
About This Manual
• Button operations are indicated using the
letters shown in the illustration.
• Each section of this manual provides you with
the information you need to perform operations
in each mode. Further details and technical
information can be found in the “Reference”
section.
Sensor
(Light)
General Guide
• The illustration below shows which buttons you need to press to navigate
between modes.
• In any mode, press L to illuminate the display.
• You can use buttons B, D, and E to directly enter a sensor mode from
the Timekeeping Mode or from another sensor mode. To enter a sensor
mode from the Stopwatch, Countdown Timer, Data Recall, or Alarm Mode,
first enter the Timekeeping Mode and then press the applicable button.
Timekeeping Mode
Altimeter Mode
Countdown
Timer Mode
Stopwatch
Mode
Digital
Compass Mode
Press C.
▲
▲
Press D.
Alarm Mode
▲
Press C.
▲
▲
Press B.
▲
Sensor Modes
▲
▲
Data Recall Mode
▲
Barometer/
Thermometer Mode
Press E.
Timekeeping
Use the Timekeeping Mode to view the current
time and date. You also need to enter the
Timekeeping Mode to configure timekeeping
settings, as well as the display illumination
duration and Power Saving setting.
• In the Timekeeping Mode, press A to toggle
between the month–day and the day of the
week–day at the top of the display.
Hour : Minutes
PM indicator
Seconds
Month – Day
Day of week
Day
Press A.
To set the time and date
1. In the Timekeeping Mode, hold down A until the seconds start to flash,
which indicates the setting screen.
2. Press C to move the flashing in the sequence shown below to select other
settings.
Year
Seconds
Hour
Minutes
Day
Month
12/24-Hour
Format
Power
Saving
3. When the timekeeping setting you want to change is flashing, use D and/
or B to change it as described below.
• The following steps explain how to configure timekeeping settings only.
4. After the settings are the way you want, press A to exit the setting screen.
Note
• For information about specifying how long the display remains illuminated,
see “To specify the illumination duration”.
• For details about configuring settings for the Power Saving feature, see
“Power Saving”.
Do this:
Press D.
Use D (+) and B (–).
Press D.
Press D (+) and B (–).
To do this:
Reset the seconds to
00
Change the hour or minutes
Toggle between 12-hour (
12H
)
and 24-hour (
24H
) timekeeping
Change the year, month, or day
Screen
• Resetting the seconds to
00
while the current count is in the range of 30 to
59 causes the minutes to be increased by 1. In the range of 00 to 29, the
seconds are reset to
00
without changing the minutes.
• With the 12-hour format, the P (PM) indicator appears on the display for
times in the range of noon to 11:59 p.m. and no indicator appears for times
in the range of midnight to 11:59 a.m.
• With the 24-hour format, times are displayed in the range of 0:00 to 23:59,
without any indicator.