Casio 2895 Watch User Manual


 
Operation Guide 2895
1
MO0403-EA
Getting Acquainted
Congratulations upon your selection of this CASIO watch. To get the most out of your
purchase, be sure to carefully read this manual and keep it on hand for later reference
when necessary.
Expose the watch to bright light to charge its battery before using it.
You can use this watch even as its battery is being charged by exposure to bright
light.
Be sure to read “Battery” of this manual for important information you need to
know when exposing the watch to bright light.
If the display of the watch is blank...
If the SLEEP indicator is on the display, it means that the
display is blank because the watch’s Power Saving
function has turned off the display to conserve power.
Power Saving automatically turns off the display and
enters a sleep state whenever your watch is left for a
certain period where it is dark.
The initial factory default setting is Power Saving on.
The watch recovers from the sleep state if you move it to
a well-lit area
*
, if you press any button, or if you angle
the watch towards your face for reading.
*
It can take up to five seconds for the display to turn on.
See “Power Saving Function” for more information.
About This Manual
Depending on the model of your watch, display text
appears either as dark figures on a light background, or
light figures on a dark background. All sample displays
in this manual are shown using dark figures on a light
background.
Button operations are indicated using the letters shown
in the illustration.
Each section of this manual provides you with the
information you need to perform operations in each
mode. Further details and technical information can be
found in the Reference section.
(Light)
(Light)
General Guide
Press C to change from mode to mode.
In any mode, press L to illuminate the display.
Countdown Timer Mode
Dual Time Mode
Timekeeping Mode
Alarm Mode
Stopwatch Mode
Press C.
Timekeeping
Use the Timekeeping Mode to set and view the current
time and date.
To set the time and date
1.In the Timekeeping Mode, hold down A until the
seconds start to flash, which indicates the setting
screen.
2.Press C to move the flashing in the sequence shown
below to select other settings.
Hour
Seconds
12/24-Hour
Format
Power Saving
Day Month
Year
Minutes
Day of week
Month Day
PM indicator
Hour : Minutes Seconds
3. When the setting you want to change is flashing, use D and B to change it as
described below.
Setting
Seconds
Hour, Minutes,
Year, Month, Day
12/24-Hour Format
Power Saving
Button Operations
Press D to reset to 00.
Use D (+) and B () to change the setting.
Press D to toggle between 12-hour (12H) and
24-hour (24H) timekeeping.
Press D to toggle Power Saving on (ON) and
off (OFF).
Screen
4. Press A to exit the setting screen.
See Power Saving Function for details about configuring Power Saving settings.
The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is
applied in all modes.
The day of the week is automatically displayed in accordance with the date (year,
month, and day) settings.
Countdown Timer
The countdown timer can be set within a range of one
minute to 60 minutes. An alarm sounds when the
countdown reaches zero. The countdown timer has two
modes: auto-repeat and elapsed time, and a progress
beeper signals the progress of the countdown. All of this
makes the countdown timer a valuable tool for timing the
start of a yacht race.
All of the operations in this section are performed in the
Countdown Timer Mode, which you enter by pressing
C.
Configuring the Countdown Timer
The following are the settings you should configure before actually using the
countdown timer.
Countdown start time and reset time
Timer mode (auto-repeat, elapsed time)
Progress beeper on/off
See To configure the countdown timer for information about setting up the timer.
Timekeeping
Mode time
Minutes
Seconds
Mode
indicator
Reset Time
You can set a reset time, which is a kind of alternate countdown start time you can
recall with the press of a button any time a countdown operation is in progress.
Timer Mode
The countdown timer gives you a choice of two modes: auto-repeat and elapsed time.
Auto-repeat
The auto-repeat mode automatically restarts the countdown from the countdown start
time you set whenever zero is reached.
The auto-repeat mode is best when timing the starts of match races.
Even if you start a countdown operation from the reset time, the countdown
automatically restarts from the countdown start time whenever it reaches zero.
Auto-repeat timing repeats up to seven times.
Elapsed Time
When the end of the countdown is reached in the elapsed time mode, the timer
automatically switches to an elapsed time measurement operation.
The elapsed time mode is best when timing the speed of yachts during ocean races.
The elapsed time operation is performed in one-second increments up to 99 hours,
59 minutes, 59 seconds.
Countdown Timer Beeper Operations
The watch beeps at various times during a countdown so you can keep informed
about the countdown status without looking at the display. The following describes the
types of beeper operations the watch performs during a countdown.
Countdown End Beeper
The watch beeps each second of the final 10 seconds before a countdown reaches
zero, and at zero. The first five beeps (seconds 10 through 6) are higher pitched than
the final five beeps (seconds 5 through 1). The watch emits a longer beep to signal
when the countdown reaches zero.
The countdown end beeper always sounds, regardless of the on/off status of the
progress beeper.
Progress Beeper
The progress beeper actually includes two beepers: a reset time beeper and a reset
period progress beeper.
The reset time beeper and reset period progress beeper sound only while the
progress beeper is turned on.
Reset Time Beeper
The reset time beeper is similar to the countdown end beeper. When the progress
beeper is turned on, the watch beeps each second of the final 10 seconds before the
countdown reaches the reset time.
Reset Period Progress Beeper
The reset period is the portion of the countdown between the reset time and zero.
When the progress beeper is turned on, the watch emits four short beeps at the top of
each minute during the reset period, and 30 seconds before the end of the
countdown.