Sony CDX-GT860U Portable CD Player User Manual


 
3
1
2
4
5
6
7
AUDIO
OUT
REAR
AUDIO
OUT
FRONT
BUS
AUDIO
IN
AUDIO OUT
REAR
AUDIO OUT
FRONT
BUS AUDIO IN
*
2
BUS
CONTROL IN
REMOTE
IN
SUB OUT (MONO)
L
R
2-898-923-21 (1)
Cautions
• This unit is designed for negative ground (earth) 12 V
DC operation only.
• Do not get the leads under a screw, or caught in moving
parts (e.g. seat railing).
• Before making connections, turn the car ignition off to
avoid short circuits.
• Connect the yellow and red power supply leads only
after all other leads have been connected.
Run all ground (earth) leads to a common
ground (earth) point.
• Be sure to in su late any loose un con nect ed leads with
electrical tape for safety.
Notes on the power supply lead (yellow)
• When connecting this unit in combination with other
stereo components, the connected car circuit’s rating
must be higher than the sum of each component’s fuse.
• When no car circuits are rated high enough, connect
the unit directly to the battery.
Parts Iist
• The numbers in the list are keyed to those in the
instructions.
• The bracket is attached to the unit before shipping.
Before mounting the unit, use the release keys to
remove the bracket from the unit. For details, see
“Removing the bracket ()” on the reverse side of the
sheet.
Keep the release keys for future use as they
are also necessary if you remove the unit from
your car.
Caution
Handle the bracket carefully to avoid injuring your
ngers.
Note
Before installing, make sure that the catches on both sides of
the bracket are bent inwards 2 mm (
3
/32 in). If the catches are
straight or bent outwards, the unit will not be installed securely
and may spring out.
Connection example
Notes (-
A
)
Be sure to connect the ground (earth) lead before connecting
the amplifi er.
The alarm will only sound if the built-in amplifi er is used.
Tip (-
B
-
)
For connecting two or more CD/MD changers, the source
selector XA-C40 (not supplied) is necessary.
Installation/Connections
Instalación/Conexiones
⫭堩濊丣嵓彂㌉
FM/AM
Compact Disc Player
Connection diagram
To a metal surface of the car
First connect the black ground (earth) lead, then connect the
yellow and red power supply leads.
To the power antenna (aerial) control lead or
power supply lead of antenna (aerial) booster
Notes
It is not necessary to connect this lead if there is no power
antenna (aerial) or antenna (aerial) booster, or with a
manually-operated telescopic antenna (aerial).
When your car has a built-in FM/AM antenna (aerial) in
the rear/side glass, see “Notes on the control and power
supply leads.”
To AMP REMOTE IN of an optional power
amplifi er
This connection is only for amplifi ers. Connecting any other
system may damage the unit.
To the interface cable of a car telephone
To a car’s illumination signal
Be sure to connect the black ground (earth) lead to a metal
surface of the car fi rst.
To the +12 V power terminal which is
energized in the accessory position of the
ignition switch
Notes
If there is no accessory position, connect to the +12 V
power (battery) terminal which is energized at all times.
Be sure to connect the black ground (earth) lead to a
metal surface of the car fi rst.
When your car has a built-in FM/AM antenna (aerial) in
the rear/side glass, see “Notes on the control and power
supply leads.”
To the +12 V power terminal which is
energized at all times
Be sure to connect the black ground (earth) lead to a metal
surface of the car fi rst.
Notes on the control and power supply leads
The power antenna (aerial) control lead (blue) supplies +12 V
DC when you turn on the tuner.
When your car has built-in FM/AM antenna (aerial) in the rear/
side glass, connect the power antenna (aerial) control lead
(blue) or the accessory power supply lead (red) to the power
terminal of the existing antenna (aerial) booster. For details,
consult your dealer.
A power antenna (aerial) without a relay box cannot be used
with this unit.
Memory hold connection
When the yellow power supply lead is connected, power will
always be supplied to the memory circuit even when the ignition
switch is turned off.
Notes on speaker connection
Before connecting the speakers, turn the unit off.
Use speakers with an impedance of 4 to 8 ohms, and with
adequate power handling capacities to avoid its damage.
Do not connect the speaker terminals to the car chassis, or
connect the terminals of the right speakers with those of the
left speaker.
Do not connect the ground (earth) lead of this unit to the
negative (–) terminal of the speaker.
Do not attempt to connect the speakers in parallel.
Connect only passive speakers. Connecting active speakers
(with built-in amplifi ers) to the speaker terminals may damage
the unit.
To avoid a malfunction, do not use the built-in speaker leads
installed in your car if the unit shares a common negative (–)
lead for the right and left speakers.
Do not connect the unit’s speaker leads to each other.
Note on connection
If speaker and amplifi er are not connected correctly, “Failure”
appears in the display. In this case, make sure the speaker and
amplifi er are connected correctly.
AUDIO OUT
FRONT
AUDIO OUT
REAR
SUB OUT (MONO)
BUS AUDIO IN
BUS CONTROL IN
A
B
Precauciones
• Esta unidad se diseñó para alimentarse sólo con cc de
12 V de masa negativa.
• No coloque los cables debajo de ningún tornillo, ni
los aprisione con partes móviles (p. ej. los raíles del
asiento).
• Antes de realizar las conexiones, desactive el
encendido del automóvil para evitar cortocircuitos.
• Conecte los cables de fuente de alimentación amarillo
y rojo solamente después de haber conectado los
demás.
Conecte todos los cables de conexión a masa
a un punto común.
• Por razones de seguridad, asegúrese de aislar con cinta
aislante los cables sueltos que no estén conectados.
Notas sobre el cable de fuente de alimentación
(amarillo)
• Cuando conecte esta unidad en combinación con otros
componentes estéreo, la capacidad nominal del circuito
conectado del automóvil debe ser superior a la suma
del fusible de cada componente.
• Si no hay circuitos del automóvil con capacidad
nominal sufi cientemente alta, conecte la unidad
directamente a la batería.
Lista de componentes
• Los números de la lista corresponden a los de las
instrucciones.
• La unidad se comercializa con el soporte . Antes
de montarla, utilice las llaves de liberación para
extraer el soporte de la misma. Para obtener más
información, consulte “Extracción del soporte ()” en
el dorso de la hoja.
Conserve las llaves de liberación para
utilizarlas en el futuro, ya que también las
necesitará si retira la unidad del automóvil.
Precaución
Tenga mucho cuidado al manipular el soporte para
evitar posibles lesiones en los dedos.
Nota
Antes de instalar la unidad, compruebe que los enganches de
ambos lados del soporte están doblados hacia adentro 2 mm.
Si no lo están o están doblados hacia afuera, la unidad no se
instalará correctamente y puede saltar.
Ejemplo de conexiones
Notas (-
A
)
Asegúrese de conectar primero el cable de conexión a masa
antes de realizar la conexión del amplifi cador.
La alarma sonará únicamente si se utiliza el amplifi cador
incorporado.
Sugerencia (-
B
-
)
Si desea conectar dos o más cambiadores de CD/MD,
necesitará el selector de fuente XA-C40 (no suminidtrado).
Diagrama de conexión
A una superfi cie metálica del automóvil
Conecte primero el cable de conexión a masa negro, y después
los cables amarillo y rojo de fuente de alimentación.
Al cable de control de la antena motorizada
o al cable de fuente de alimentación del
amplifi cador de señal de la antena
Notas
Si no se dispone de antena motorizada ni de amplifi cador
de antena, o se utiliza una antena telescópica accionada
manualmente, no será necesario conectar este cable.
Si el automóvil incorpora una antena de FM/AM en el cristal
trasero o lateral, consulte “Notas sobre los cables de control y
de fuente de alimentación”.
A AMP REMOTE IN de un amplifi cador de
potencia opcional
Esta conexión es sólo para amplifi cadores. La conexión de
cualquier otro sistema puede dañar la unidad.
Al cable de interfaz de un teléfono para
automóvil
A una señal de iluminación del automóvil
Asegúrese de conectar primero el cable de conexión a masa
negro a una superfi cie metálica del automóvil.
Al terminal de alimentación de +12 V que
recibe energía en la posición de accesorios del
interruptor de la llave de encendido
Notas
Si no hay posición de accesorios, conéctelo al terminal
de alimentación (batería) de +12 V que recibe energía sin
interrupción.
Asegúrese de conectar primero el cable de conexión a masa
negro a una superfi cie metálica del automóvil.
Si el automóvil incorpora una antena de FM/AM en el cristal
trasero o lateral, consulte “Notas sobre los cables de control y
de fuente de alimentación”.
Al terminal de alimentación de +12 V que recibe
energía sin interrupción
Asegúrese de conectar primero el cable de conexión a masa
negro a una superfi cie metálica del automóvil.
Notas sobre los cables de control y de fuente de alimentación
El cable de control de la antena motorizada (azul) suministrará cc
de + 12 V cuando conecte la alimentación del sintonizador.
Si el automóvil dispone de una antena de FM/AM incorporada en
el cristal trasero o lateral, conecte el cable de control de antena
motorizada (azul) o el cable de entrada de alimentación auxiliar
(rojo) al terminal de alimentación del amplifi cador de antena
existente. Para obtener más información, consulte a su distribuidor.
Con esta unidad no es posible utilizar una antena motorizada sin
caja de relé.
Conexión para protección de la memoria
Si conecta el cable de fuente de alimentación amarillo, el circuito
de la memoria recibirá siempre alimentación, aunque apague el
interruptor de encendido.
Notas sobre la conexión de los altavoces
Antes de conectar los altavoces, desconecte la alimentación de la
unidad.
Utilice altavoces con una impedancia de 4 a 8 con la capacidad
de potencia adecuada para evitar que se dañen.
No conecte los terminales de altavoz al chasis del automóvil, ni
conecte los terminales del altavoz derecho con los del izquierdo.
No conecte el cable de conexión a masa de esta unidad al
terminal negativo (–) del altavoz.
No intente conectar los altavoces en paralelo.
Conecte solamente altavoces pasivos. Si conecta altavoces
activos (con amplifi cadores incorporados) a los terminales de
altavoz, puede dañar la unidad.
Para evitar fallas de funcionamiento, no utilice los cables de
altavoz incorporados instalados en el automóvil si la unidad
comparte un cable negativo común (–) para los altavoces derecho
e izquierdo.
No conecte los cables de altavoz de la unidad entre sí.
Nota sobre la conexión
Si el altavoz y el amplifi cador no están conectados correctamente,
aparecerá “Failure” en la pantalla. Si es así, compruebe la conexión
del altavoz y el amplifi cador.
Enganche
Equipment used in illustrations (not supplied)
Equipo utilizado en las ilustraciones (no suministrado)
㌶♢ᶑ䗨堩仒濃ᵱ斨彥濄
from car antenna (aerial)
desde la antena del automóvil
㯡廊⢍丣
Rear speaker
Altavoz posterior
⍲仒㇐⡔◌
Front speaker
Altavoz frontal
↱仒㇐⡔◌
Active subwoofer
Altavoz potenciador de
graves activo
㙭㷴峩Ẳ㇐⡔◌
Power amplifi er
Amplifi cador de potencia
∃䋫㒢
Catch

× 2
× 4
CD/MD changer
Cambiador de CD/MD
DE0NE!㋆䠃㚞
BUS AUDIO IN
BUS CONTROL IN
Source selector*
Selector de fuente*
㷴彭㉍◌*
XA-C40
* not supplied
no suministrado
! ᵱ斨彥
㱌び
!㚐㚞⍎偡ợ岃㌉⚔䗨!23!W!䙘㲥䒙㷴Ɂ
!≣ợ䒙丣⢝⚌圞揭ᵯ濇ㅺ亄⚌䥟∌恌Ṛᵮ濃⣦⸋㡩
濄Ɂ
!彂㌉丣嵓ᶯ↱濇孛⃗救㯡廊䀝⹤⃗濇ṉ忣₱䝑
嵓Ɂ
!⍎㙭彂㌉ᷪㆤ㙭⃚Ḻ⭠丣ᶯ⍲濇⃱彂㌉
䒙㷴廷⭠丣Ɂ
!⭪ㆤ㙭⚔丣恡彂㌉↔⍰㌉⚔䀝Ɂ
!ᶞᷪ⫭⃌濇孛∅⼩乁乼做ⶊợㆤ㙭㛢㓇㚎彂㌉䗨
䒙丣乁乼Ɂ
⃗ᷲ䒙㷴⭠丣濃渨濄䗨㱌びᷯ柝
!⭪㚐㚞ᵲ⃚⫧ặ⡔堩仒丨⍬ợ㕚濇ㆤ彂㌉䗨㯡
廊䒙嵓⬝愳⼩柟ᷲ⍨堩仒ὁ旍ᶁ⬝愳䗨⾟⏰Ɂ
!⺷㯡廊䒙嵓⬝愳ᵱ⢃㕚濇孛⭪㚐㚞䙘㌉ᵲ吨䒙㯄
䙜彂㌉Ɂ
晚Ṛ夬埌!
!埌ᶑ㓔⪻ᵲ存㕲᷊ᶑ䗨㓔⪻㖓兘䗨Ɂ
!堩⋜㜚!!㖓弴廷ᶯ↱堩⚌㚐堩仒ᵮ䗨Ɂ⫭堩㚐
堩仒ᶯ↱濇ợ⹤摥搉≽!!Ḳ㚐堩仒ᵮ⌺ᵯ堩⋜
㜚!Ɂ孊个⃩⬝濇孛⌦敩㚐柙⌱䗨ĥ㈪⋜堩
㜚!)*ĦɁ
!ὁ⪼⣡⹤摥搉≽!!ṉ⡫⍲Ɂ「Ḳ㯡廊ᵮ⌺ᵯ㚐
堩仒㕚濇㙭⼩壥↔孉搉≽Ɂ
㱌び
⭳⼧堩⋜㜚!
!ṉ₱Ẉ↔㉫Ɂ
⫭堩↱濇孛䟒嬈堩⋜㜚!
!ᶈ弝䗨♞⫾⍵⃩⺓㙖!3!nnɁ⣦㜀
♞⫾䩸䙘ㅺ⍵⡺⺓㙖濇㚐堩仒⭪ᵱ偡䇆♞⫭堩ⷚ⍓偡⺝⅞Ɂ
丣嵓彂㌉♢ữ!
㱌!(-A)
!∅⼩⚌彂㌉㒢◌ᶯ↱彂㌉㌉⚔丣Ɂ
!⍎㙭⚌ợ⃩仒䗨㒢◌㕚濇嫊㈉ㆱṾ⌵⅞⡔␱Ɂ
-B-
剉壥彂㌉!3!⍔ㅺ㙘⡾!DE0NE!㋆䠃㚞濇⼩柟ợ䒌杗㷴彭㉍◌!
YB.D51濃ᵱ斨彥濄Ɂ
♞⫾
丣嵓彂㌉♢!
!㯡廊⯂埌
€彂㌉渵凖⚔丣濇䂚⍲彂㌉渨⏰丆䒙㷴⭠丣Ɂ
!䒙∌⢍丣㌋↚⭠丣ㅺ⢍丣⊫亍◌䗨䒙㷴⭠丣
!⣦㜀㰅㙭䒙∌⢍丣ㅺ⢍丣⊫亍◌濇ㅺ㙭∌ẜ亍⹳⢍丣濇
晤彂㌉㫈⭠丣Ɂ
!剉㯡廊䗨⍲0Ἃ䌟䏧⃩㙭⃩仒!GN0BN!⢍丣濇孛⌦敩ĥ⃗ᷲ
㌋↚⭠丣⏰䒙㷴⭠丣䗨㱌びᷯ柝ĦɁ
!彭岑䗨∃䋫㒢◌䗨!BNQ!SFNPUF!JO
㫈彂㌉ḩᷲ㒢◌Ɂ彂㌉ṟẹ⃚⫧䱟乃⍓偡Ṿ㋃⚳㚐堩
仒Ɂ
!廊廡䒙孁㌉䒙乪
!㯡廊䃋㕲ὅ⍛
⼩柟€⭪渵凖⚔丣彂㌉㯡廊䗨⯂埌Ɂ
!!,23!W!䒙㷴䩓濇孉䩓⚌䀝⹤⃗斨Ṛằ仒
彾䒙
!⣦㜀㰅㙭斨Ṛằ仒濇ⅽ彂㌉!,23!W!䒙㷴濃吨䒙㯄濄䩓
濇孉䩓旳㕚⡨ᷲ彾䒙䈚⽥Ɂ
!䟒ὁ€⭪渵凖⚔丣彂㌉㯡廊⯂埌Ɂ
!剉㯡廊䗨⍲0Ἃ䌟䏧⃩㙭⃩仒!GN0BN!⢍丣濇孛⌦敩ĥ⃗ᷲ
㌋↚⭠丣⏰䒙㷴⭠丣䗨㱌びᷯ柝ĦɁ
!!,23!W!䒙㷴䩓濇孉䩓旳㕚⡨ᷲ彾䒙䈚⽥
䟒ὁ€⭪渵凖⚔丣彂㌉㯡廊⯂埌Ɂ
⃗ᷲ㌋↚⭠丣⏰䒙㷴⭠丣䗨㱌びᷯ柝
!㌉彾孧孴◌䒙㷴㕚濇䒙∌⢍丣䗨㌋↚⭠丣濃呁濄ἣ偡㌴ỿ!
,23!W!䙘㲥䒙Ɂ
!⺷㯡廊䗨⍲0Ἃ䌟䏧䧻ᵮ㙭⃩仒!GN0BN!⢍丣㕚濇孛⭪䒙∌⢍丣
㌋↚丣濃呁濄ㅺ斨Ṛ䒙㷴⭠丣濃丆濄彂㌉䌔㙭⢍丣⊫亍
◌ᵮ䗨䒙㷴䩓ᵮɁ孊个存㕲濇孛ᵲ「䗨丳摤⒪侸䱟Ɂ
!㚐㚞ᵱ偡ợᵱ⃛⡫之䒙◌䘶䗨䒙∌⢍丣Ɂ
ὁ㉥嬔⼪䗨丣嵓彂㌉㰹
⺷彂㌉ᷪ渨䗨䒙㷴⭠丣㕚濇⋗ợ䀝⹤⃗⃗救濇䒙㷴ḱ⭪⭝嬔
⼪䒙嵓ỿ䒙Ɂ
⃗ᷲ㇐⡔◌彂㌉䗨㱌びᷯ柝
!彂㌉㇐⡔◌ᶯ↱濇孛⃗救㚐㚞䒙㷴Ɂ
!孛ợ斟ㇻᶞ!5.9!㪋⤪ᵸ⃛㙭⢃∃䋫⡨䍪偡䗨㇐⡔◌濇ṉ
₱㋃⚳Ɂ
!≣⭪㇐⡔◌䩓彂㌉↔㯡廊ⷹ䘼ᵮ濇ㅺ⭪⍗㇐⡔◌䗨䩓ᵲⵊ
㇐⡔◌䗨䩓彂㌉Ɂ
!≣⭪㚐㚞䗨⚔丣彂㌉↔㇐⡔◌䗨岃㛥濃.濄䩓ᵮɁ
!㇐⡔◌ᵱ⍓ⷚ侸彂㌉Ɂ
!孛ḩ彂㌉㷴㇐⡔◌Ɂ⭪㙭㷴㇐⡔◌濃⃛㙭⃩仒㒢◌濄彂㌉
↔㇐⡔◌䩓⍓偡Ṿ㋃⚳㚐㚞Ɂ
!剉㚐㚞ợⵊɀ⍗㇐⡔◌䗨⃕岃㛥濃.濄䒙丣濇ᶞᷪ忣₱㒩
昀濇Ⅻ≣ợ⫭堩⚌㯡廊⃩䗨⃩仒㇐⡔◌䒙丣Ɂ
!孛≣⭪㚐㚞㇐⡔◌䒙丣䙜᷶彂㌉Ɂ
彂㌉䗨㱌びᷯ柝
⣦㜀㚎㫇䟒彂㌉㇐⡔◌⏰㒢◌濇ⅽ㖢⮳ᵮṾ⅞
䌔ĥGbjmvsfĦɁ弽㕚濇孛䟒ὁ㇐⡔◌⏰㒢◌彂㌉㫇䟒Ɂ
AMP REM
Max. supply current 0.3 A
Corriente máx. de alimentación de 0,3 A
䒙㲥!1/4!B
Fuse (10 A)
Fusible (10 A)
ὁ旍ᶁ!)21!B*
Blue/white striped
Con rayas azules y blancas
䗡凖㛅丝
Red
Rojo
Yellow
Amarillo
White
Blanco
䗡凖
Green
Verde
Purple
Morado
White/black striped
Con rayas blancas y negras
䗡凖渵凖㛅丝
Grey/black striped
Con rayas grises y negras
渵凖㛅丝
Green/black striped
Con rayas verdes y negras
渵凖㛅丝
Grey
Gris
Left
Izquierdo
Right
Derecho
Left
Izquierdo
Right
Derecho
ANT REM
Black
Negro
渵凖
Blue
Azul
Max. supply current 0.1 A
Corriente máx. de alimentación de 0,1 A
䒙㲥 1/2!B
Purple/black striped
Con rayas moradas y negras
渵凖㛅丝
Source selector
(not supplied)
Selector de fuente
(no suminidtrado)
㷴彭㉍◌
)ᵱ斨彥*
XA-C40
Supplied with the CD/MD changer
Suministrado con el cambiador de CD/MD
斨ⶊᷲ!DE0NE!㋆䠃㚞
*
1
CDX-GT860U
©
2007 Sony Corporation Printed in Thailand
Orange/white striped
Con rayas naranjas y blancas
0䗡凖㛅丝
Light blue
Azul celeste
㵅呁
ATT
ILLUMINATION
*
1
Rotary commander RM-X4S
Mando rotatorio RM-X4S
㔯廐⹳忉㌋◌!SN.Y5T
*
1
RCA pin cord (not supplied)
*
2
Be sure to match the colour-coded
cord for audio to the appropriate jacks
from the unit.
*
3
Supplied with XA-C40
*
4
Insert with the cord upwards.
*
1
Cable con terminales RCA
(no suministrado)
*
2
Asegúrese de hacer coincidir el cable
de audio codifi cado con colores con
las tomas correspondientes de la
unidad.
*
3
Suministrado con el XA-C40
*
4
Insertar con el cable hacia arriba.
*
1
!SDB!揬⹳䒙丣濃ᵱ斨彥濄
*
2
!䟒ὁ柵⭠丣栀ᵲ堩仒ᵮ䗨㫇䟒㌶⪸
䙜⭝ⷸɁ
*
3
斨ⶊᷲ!YB.D51
*
4
!䒙丣⍵ᵮ㌶Ɂ
*
4
*
3