APC NET7N-J Surge Protector User Manual


 
Thank you for selecting APC SurgeArrest! It has been designed
to provide the highest value of protection against spikes and
EMI/RFI noise on electrical lines.
Save these instructions for future reference!
SAFETY PRECAUTIONS
Do not install this device during a lightning storm!
The SurgeArrest is intended for a cool (0-40 °C) and dry
indoor environment with relative humidity of 0-95% non-
condensing. Do not install the SurgeArrest near heaters or
in a hot environment. Do not install the SurgeArrest in an
excessively moist or potentially wet environment, for example:
near bathtub, sinks, pools etc.
The SurgeArrest is intended to supply electric power to
computers, peripheral, and electronic equipment. The
SurgeArrest is rated for 100 VAC, 50/60 Hz, and 15 Amps
maximum.
For best protection against spikes induced by lightning
storms, it is hightly recommended that the SurgeArrest surge
suppressor be grounded to earth.
Figure 1
Product Features
Please refer to Figure 1 for the following information and
instructions.
➀✎ The Power Cord is designed for a three wire system (two
wires carry power and the third is connected to earth). A
two to three wire Adapter Plug is provided for two wire re-
ceptacles.
. Each SurgeArrest has a built-in ON/OFF Power Switch to
allow the user to activate electricity to connected equipment
such as computers, printers, terminals etc.
. The POWER ON indicator is activated when the Power
Switch is ON and the unit is receiving electricity.
SurgeArrest
. The Protection Working indicator is activated as long
as the thermal fuse is intact. If this indicator is extinguished,
the product disconnects from the utility line. In this case,
return this unit to APC for repair or replacement.
. Seven Outlets are provided for your convenience.
. Telephone Protector/ Network Port Protector (optional)
Model Pro7T-J hasa built-in one line (two wire) telephone
protector. A six foot telephone extension cord is provided.
Model Net7N-J has a built-in network protector. Network
Port Protector (for 10BaseT, 100BaseT, 100BaseTX,
100BaseT4, 100VG-AnyLAN, & Token Ring interface cards
& HUBs).
Note: Never connect an ISDN line to a SurgeArrest•.
. Each SurgeArrest is equipped with a 15 Amp circuit
breaker to protect against electrical power overload. Button
will pop up in the event of an overload. If this happens, un-
plug at least one piece of equipment, and reset button.
. A 3 prong to 2 prong Plug Adaptor is provided for your
convenience. See figure 3.
Figure 2
Installation Instructions
1. Turn OFF Power Switch . The switch lever marked with
the “O” should be down.
2. Connect the Power Cord into a 100VAC receptacle. It
is highly recommended that a grounded receptacle be
used. If your receptacle is ungrounded (accepts only
plugs with two blades), attach the 3 to 2 Plug Adapter
that is supplied with the unit. The Adapter Plug has a
green wire that is used to connect to earth ground where
permitted or accessible. Please note that ungrounded
surge protectors do not provide effective surge protec-
tion between line to ground. Check local electrical laws
governing grounding practices. See Figure 3 below.
Figure 3
3. Connect power cords of electrical equipment to be pro-
tected into the Outlets on the SurgeArrest.
4. For model Pro7T-J, protect your telephone, fax machine,
or modem by connecting the supplied telephone exten-
sion cord into the telephone jack on the wall and con-
necting the other end into the jack marked “IN” on the
SurgeArrest. Connect your telephone equipment cord
on the jack marked “OUT” on the SurgeArrest.
5. For model Net7N-J, protect your local area network card
by connecting the LAN cable from the Concentrator
HUB to the “IN” jack on the SurgeArrest. Connect one
end of the supplied cable to the network card jack and
connect the other end to the “OUT” jack on the
SurgeArrest.
6. Turn ON the SurgeArrest power switch.
7. Turn ON connected equipment.
Note: Installation example is shown in Figure 4.
Figure 4
Mounting the SurgeArrest on a wall
The SurgeArrest has two mounting holes located on the bot-
tom of the unit. These holes were designed to hook on to
screw heads or nail heads. The spacing between the center of
the screw holes is 11.43 cm. For best results, when fastening
screws or nails into a wall, leave about 3.5 mm spacing be-
tween the wall and the bottom flange of the screw or nail.
Specifications
Unless otherwise stated, ratings are based on ambient tem-
perature of 20°C.
Operating Temperature Range: 0°C to 40°C
Operating Voltage: 100 VAC, 50/60 Hz
Operating Relative Humidity: 0 - 95% non-condensing
Safety Approval: Dentori T-mark
For more a detailed specification, contact APC.
Table 1: AC Surge Performance Ratings
Customer Service/Technical Support
APC Japan
BR Gotanda 7th Floor
2-30-4 Nishi-gotanda
Shinagawa-ku, Tokyo 141
Japan
Phone: 03-5434-2021
Fax: 03-5434-2022
Free dial: 0120-80-60-90 (within Japan only)
American Power Conversion
132 Fairgrounds Road
West Kingston, Rhode Island 02892
USA
Internet Address: http://www.apcc.com
Parameter/Model Professional Network
EMI/RFI Noise
Rejection (100kHz 25-60 dB 40-90 dB
to 10MHz)
Cat. A Normal Mode
Let Through Voltage <1.4% <0.6%
% of 6kV pulse
Total Energy Capacity 420J 680J
Peak Surge Current
(with 8x20µs pulse) 13kA 17.5kA
Normal Mode
Peak Surge Current
(with 8x20µs pulse) 11kA 22kA
Common Mode
Table 2: Telephone Protector Ratings
Parameter/Model Professional Network
Operating Voltage 220VDC --
Peak Surge Current
(with 8x20µs pulse) 150A --
All Modes
Number of Lines 1 --
Protected
Connector Type RJ45 --
Series Resistance 6−12Ω --
Table 3: Network Protector Ratings
Parameter/Model Professional Network
Operating Voltage -- 8VDC
EIA/TIA 568 -- Category
Performance 5
Peak Surge Current
(with 8x20µs pulse) -- 500A
Differential Modes
Peak Surge Current
(with 8x20µs pulse) -- 150A
Common Mode
Connector Type -- RJ45
Limited Product Warranty
American Power Conversion offers a limited two year war-
ranty on SurgeArrest surge suppressors.
APC warrants its products to be free from defects in materi-
als and workmanship under normal use and service for two
years for the original purchaser. Its obligation under this
warranty is limited to repairing or replacing, at its sole op-
tion, any such defective products. To obtain service under
warranty you must obtain a Returned Material Authoriza-
tion (RMA) number from APC or an APC service center with
transportation charges prepaid and must be accompanied
by a brief description of the problem and proof of date of
purchase. This warranty applies only to the original pur-
chaser.
Part Number: 990-0167 Rev. 1 12/97