Filter
Top Products
LEDs
7106505501 REV1.0.1
Exit
Next
Choose Region Wireless Settings Review SettingsStart
Please click Next to set up the Range Extender or click Exit to go to the Device Management Page.
Main Router/AP WiFi Network Name(SSID):
Exit
Next
Wi-Fi Network Name_2.4GHz:
Wi-Fi Network Name_5GHz:
Connection Status:
N/A
N/A
Disconnected
Choose Region Wireless Settings Review SettingsStart
Quick
Installation
Guide
AC750 WiFi Range Extender
RE210
Two easy setup options:
Option 1: Using a Web Browser
Option 2: Using WPS (Wi-Fi Protected Setup)
Disconnect the Ethernet (wired) connection to
your computer. Click the Wi-Fi icon on the
taskbar and connect to the extender's network
(e.g. TP-LINK_Extender_2.4GHz or _5GHz ). No
password is required to connect the rst time.
4
A. On the Start screen, click Next.
D. Enter the main router’s Wi-Fi password and
either choose Copy from Main Router/AP
or Customize to create a new name for the
2.4GHz extended network, then click Next.
E. Repeat step C and D to extend the 5GHz wireless
network.
F. Verify your Wireless Settings and click Finish.
Both 2.4GHz and 5GHz LEDs should turn
on and stay solid green.
B. Choose your region from the Region drop-down
list and click Next.
Note: Per FCC regulations, all Wi-Fi products marketed in
the U.S. are xed to the U.S. region only.
C. Select your router’s 2.4GHz wireless network
name (SSID) and click Next. If the SSID is
hidden, select the Set SSID and MAC
manually option.
Follow the Quick Setup Wizard to congure the extender.
3
Launch a web browser and type
http://tplinkrepeater.net in the address eld.
Use admin (all lowercase) for both Username
and Password to log in.
http://tplinkrepeater.net
admin
admin
Username:
Password:
Login
Cancel
Login
Congure
1
Plug the extender into an electrical outlet
near your router, and wait until the Power
LED is lit and solid green.
1
OPTION
Using a Web Browser
Power On
A. Plug the extender into an electrical outlet
about halfway between your router and the
Wi-Fi dead zone.
B. Wait about 1 minute until the RE LED is lit
and stay solid.
Ideal Range Extender Placement
5
Relocate
2
Connect
Signal MAC Channel Security
00-0A-EB-74-06-06 1 WPA-PSK
0C-72-2C-B3-A5-2C 1 WPA-PSK
Available Wireless Networks (2.4GHz): 24
Choose SSID
TP-LINK_2.4GHz_XXX
TP-LINK_XXX
Back
Rescan
Next
√
Choose Region Wireless Settings Review SettingsStart
Set SSID and MAC Manually
TP-LINK_2.4GHz_XXX
00-0A-EB-74-06-06
Most Secure(WPA-PSK/WPA2-PSK)
123456789
Back
Next
TP-LINK_2.4GHz_XXX_EXT
Choose Region
Wireless Settings Review Settings
Start
Main Router/AP Network (2.4GHz)
Main Router/AP WiFi Network Name(SSID):
Main Router/AP MAC Address(BSSID):
WiFi Security Option:
Fill in the WiFi Password of your Main
Router/AP:
Range Extender Network (XXGHz)
Range Extender WiFi Network Name(SSID):
Copy from Main Router/AP TP-LINK_2.4GHz_XXX
Customize
TP-LINK_5GHz_XXX
00-0A-EB-74-06-06
Most Secure(WPA-PSK/WPA2-PSK)
123456789
Back
Next
TP-LINK_5GHz_XXX_EXT
Choose Region Wireless Settings Review SettingsStart
Main Router/AP Network (5GHz)
Main Router/AP WiFi Network Name(SSID):
Main Router/AP MAC Address(BSSID):
WiFi Security Option:
Fill in the WiFi Password of your Main
Router/AP:
Range Extender Network (XXGHz)
Range Extender WiFi Network Name(SSID):
Copy from Main Router/AP TP-LINK_5GHz_XXX
Customize
Wireless Setting
Main Router/AP WiFi Network Name (2.4GHz):
Main Router/AP WiFi Network Name (5GHz):
Range Extender WiFi Network Name (2.4GHz):
WiFi Security Option:
WiFi Password:
Range Extender WiFi Network Name (5GHz):
WiFi Security Option:
WiFi Password:
TP-LINK_2.4GHz_XXX
TP-LINK_5GHz_XXX
TP-LINK_2.4GHz_XXX_EXT
Most Secure (WPA/WPA2-PSK)
123456789
TP-LINK_5GHz_XXX_EXT
Most Secure (WPA/WPA2-PSK)
123456789
Choose Region Wireless Settings Review SettingsStart
Back
Finish
Export Settings
Both 2.4GHz and 5GHz extended networks share the same Wi-Fi password as your main network, but
may have dierent wireless network names if you customize the names during the conguration.
Region: Please Select Your Region
Please select your own region to prevent illegal usage against the local law.
Connection are available
Not connected
Wireless Network Connection
Connect automatically Connect
TP-LINK_Extender_2.4GHz
√
Main Network Extended Network
Reset
LED
Blinking green: WPS connection is in progress.
Solid green: The extender is connected to the
router and is in a good location.
Solid orange: The extender is connected to the
router, but is too close to the router.
Solid red: The extender is connected to the router,
but is too far away from the router.
O: No active connection.
(RE)
(5GHz)
(2.4GHz)
(Power)
On: The extender is connected to the 2.4GHz
wireless network of your main Router/AP.
O: No connection.
On/O: The extender is on or o.
Blinking: The extender is initializing.
RE
Power
5GHz
2.4GHz
On: The extender is connected to the 5GHz
wireless network of your main Router/AP.
O: No connection.
Solid green Solid red Solid orange
Too far away
from the router
Too close to
the router
Good
connection